#This is a comment line, and should be ignored

# %% is read as a steps per order control line
# && is read as a phasemap control line
# they are only executed if either of them needs refreshing,
# as determined by the console

# Commands and args are:
# spectrum: [lambda, zone settings file, file name format]
# stepsperorder: [lambda, start volt offset, stop volt offset, step size, number of scans]
# phasemapper: [lambda]
# shutterclose: [dummy]
# shutdownspex: [dummy]
# cameraset: [exposure time, gain]
# runscript: [name of idl pro file to run, no extension needed]
# mirror: [home_sky | home_cal | drive_sky | drive_cal]
# cal_switch: [calibration source number]

set_status: [`Start Schedule`]


#%% stepsperorder: [632.8, 550, 680, 4, 20, 1, .05]
#&& phasemapper: [1, 1, 632.8, 632.8, 1, 0.05, 3]

set_status: [`Home Motors`]
mirror: [home_cal]


ifsea: [-100, -6] [cont]

	set_status: [`Spectra: laser`]
	cameraset: [0.25, 5]
	filter: [1]
#	cal_switch: [4]	
	spectrum: [632.8, default_zones.txt, `Y$_doy$_Date_0n$_0d$_CAL_6328_NZ0115.nc`]

	set_status: [`Obs: Red & Green`]
	cameraset: [0.25, 200]
	filter: [2]
	spectrum: [630.0, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_6300_NZ0115.nc`]	
	filter: [3]
	spectrum: [557.7, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_5577_NZ0115.nc`]
	filter: [2]
	spectrum: [630.0, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_6300_NZ0115.nc`]	
	filter: [3]
	spectrum: [557.7, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_5577_NZ0115.nc`]#
	filter: [2]
	spectrum: [630.0, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_6300_NZ0115.nc`]	
	filter: [3]
	spectrum: [557.7, default_zones.txt, `Y$_doy$_Date_0n$_0d$_SKY_5577_NZ0115.nc`]	

	ifut: [5, 6] [begin]
	   runscript: [southpole_ftp_data]
	ifut: [5, 6] [end]
	ifut: [9, 10] [begin]
	   runscript: [southpole_ftp_data]
	ifut: [9, 10] [end]
	ifut: [13, 14] [begin]
	   runscript: [southpole_ftp_data]
	ifut: [13, 14] [end]

	
ifsea: [-100, -6] [loop]


cameraset: [0.30, 2]
filter: [1]

ifsea: [-6, 100] [cont]

	set_status: [`Idle`]
	shutterclose: [1]
	shutdownspex: [1]	
	runscript: [southpole_ftp_data]
	set_status: [`Idle`]	
ifsea: [-6, 100] [loop]